Editing PlutoSDR Sink

Jump to: navigation, search

Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision Your text
Line 1: Line 1:
 
<!-- PlutoSDR_Sink.mediawiki -->
 
<!-- PlutoSDR_Sink.mediawiki -->
The PlutoSDR (a.k.a. ADALM-PLUTO) is a low-cost SDR made by Analog Devices, based on a [https://en.wikipedia.org/wiki/Product_binning binned] version of the AD9364 RFIC (same RFIC as in the USRP B200) which AD labels AD9363. It is set to operate between 325 MHz and 3.8 GHz can be extended to a range of 70 MHz to 6 GHz using simple "hack" described at [https://wiki.analog.com/university/tools/pluto/users/customizing the bottom of this page] (note that there is no performance guarantee in the extended range), and has a max sample rate of 56 MHz, but because it only has USB 2.0, the 56 MHz can only be acheived in short bursts.  The max sample rate when continuously transmitting is more like 4 or 5 MHz.  It has a  Xilinx Zynq Z-7010 FPGA + ARM CPU on board, the ARM CPU runs a lightweight version of linux.  It's set up to run as an IP device; the USB port on it appears as a USB to ethernet bridge.  It also shows up as a mass storage device which lets you easily change the config (e.g. IP address) or load new firmware.
+
The PlutoSDR (a.k.a. ADALM-PLUTO) is a low-cost SDR made by Analog Devices, based on a [https://en.wikipedia.org/wiki/Product_binning binned] version of the AD9364 RFIC (same RFIC as in the USRP B200) which AD labels AD9363. It can operate from 70 MHz to 6 GHz using simple "hack" described at [https://wiki.analog.com/university/tools/pluto/users/customizing the bottom of this page], and has a max sample rate of 56 MHz, but because it only has USB 2.0, the 56 MHz can only be acheived in short bursts.  The max sample rate when continuously transmitting is more like 4 or 5 MHz.  It has a  Xilinx Zynq Z-7010 FPGA + ARM CPU on board, the ARM CPU runs a lightweight version of linux.  It's set up to run as an IP device; the USB port on it appears as a USB to ethernet bridge.  It also shows up as a mass storage device which lets you easily change the config (e.g. IP address) or load new firmware.
  
 
For more info on getting the PlutoSDR installed and running, see this page https://wiki.analog.com/resources/tools-software/linux-software/gnuradio.
 
For more info on getting the PlutoSDR installed and running, see this page https://wiki.analog.com/resources/tools-software/linux-software/gnuradio.
Line 13: Line 13:
  
 
; Sample Rate
 
; Sample Rate
: Sample rate in samples per second, this will define how much bandwidth your SDR transmits (the RF bandwidth parameter below just defines the filter). limits: >= 520833 and <= 61440000.  A FIR filter needs to be loaded or set to auto for values below 2.083 MSPS.
+
: Sample rate in samples per second, this will define how much bandwidth your SDR transmits (the RF bandwidth parameter below just defines the filter). limits: >= 520833 and <= 61440000
  
 
; RF Bandwidth
 
; RF Bandwidth
Line 22: Line 22:
  
 
; Cyclic
 
; Cyclic
: Set to “true” if the “cyclic” mode is desired. In this case, the first buffer of samples will be repeated on the PlutoSDR until the program is stopped. The PlutoSDR IIO block will report its processing as complete: the blocks connected to the PlutoSDR IIO block won't execute anymore, but the rest of the flow graph will.
 
  
 
; Attenuation TX1 (dB)
 
; Attenuation TX1 (dB)

Please note that all contributions to GNU Radio are considered to be released under the Creative Commons Attribution-ShareAlike (see GNU Radio:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To edit this page, please answer the question that appears below (more info):

Cancel | Editing help (opens in new window)