Block used to stream samples to a USRP device (i.e. act as the transmitter).
To adjust parameters like Center Frequency while running, use QT GUI Range or another control.
There is no need to use a Throttle block when a hardware sink like a USRP Sink is used, because the USRP acts as the throttle.
The input message port called "command" can be used to change frequency, gain, and other parameters via Message Passing. A common arrangement is to use the QT GUI Frequency Sink's output message port and connect it to the USRP Source/Sink's input port, so that when a user double-clicks within the GUI to change frequency, the change gets propagated to the USRP device.
Output Type - This parameter controls the data type of the output stream in GNU Radio.
Wire Format - This parameter controls the form of the data over the bus/network. Complex bytes may be used to trade off precision for bandwidth. Not all formats are supported on all devices.
Stream Args - Optional arguments to be passed in the UHD streamer object. Streamer args is a list of key/value pairs; usage is determined by the implementation. Docs for stream args
Stream Channels - Optionally used to specify which channels are used, e.g. [0,1]
Devices Address - The device address is a delimited string used to locate UHD devices on your system. If left blank, the first UHD device found will be used. Use the device address to specify a specific device or list of devices.
Examples: serial=12345678 addr=192.168.10.2 addr0=192.168.10.2, addr1=192.168.10.3
Device Arguments - Other various arguments that can be passed to the USRP Source, see USRP Device Configuration
Sync - Can be used to get USRP to attempt to sync to either PC's clock, or PPS signal if it exists.
Clock Rate [Hz] - The clock rate shouldn't be confused with sample rate, but they are related. The B2X0 and E31X USRPs use a flexible clock rate that will either be equal to the requested sample rate, or a multiple of it. Best left to default unless specific behavior is needed.
Num Mboards - Selects the number of USRP motherboards (i.e. physical USRP devices) in this device configuration.
Mbx Clock Source - Where the motherboard should sync its time and clock references. External refers to the 10 MHz and PPS input on the USRP. O/B GPSDO is the optional onboard GPSDO module, which provides its own 10 MHz and PPS signals.
Mbx Subdev Spec - Each motherboard should have its own subdevice specification and all subdevice specifications should be the same length. Select the subdevice or subdevices for each channel using a markup string. The markup string consists of a list of dboard_slot:subdev_name pairs (one pair per channel). If left blank, the UHD will try to select the first subdevice on your system. See the application notes for further details.Single channel example: ":AB"
Num Channels - Selects the total number of channels in this multi-USRP configuration. Ex: 4 motherboards with 2 channels per board = 8 channels total.
Sample Rate - The number of samples per second, which is equal to the bandwidth in Hz we wish to observe. The UHD device driver will try its best to match the requested sample rate. If the requested rate is not possible, the UHD block will print an error at runtime.
Chx Center Frequency - The center frequency is the overall frequency of the RF chain.
Chx Gain Value - Value used for gain, which is either between 0 and the max gain for the USRP (usually around 70 to 90), when using the default "Absolute" Gain Type. When using "Normalized" Gain Type, it will always be 0.0 to 1.0, where 1.0 will be mapped to the max gain of the USRP being used.
Chx Gain Type - Absolute (in dB) or Normalized (0 to 1)
Chx Antenna - For subdevices with only one antenna, this may be left blank. Otherwise, the user should specify one of the possible antenna choices. See the daughter-board application notes for the possible antenna choices.
Chx Bandwidth - The bandwidth used by the USRP's anti-aliasing filter. To use the default bandwidth filter setting, this should be zero. Only certain subdevices have configurable bandwidth filters. See the daughterboard application notes for possible configurations.
Chx Enable DC Offset Correction - Attempts to remove the DC offset, i.e. the average value of a signal, which is something that will be very visible in the Frequency domain.
Chx Enable IQ Imbalance Correction - Attempts to correct any IQ imbalance, which is when there is a mismatch between the I and Q signal paths, typically causing a stretching effect to a constellation.