# Sample Rate Tutorial

## Demonstrate the effects of Sample Rate with GRC[edit]

The following flowgraph will be used to demonstrate the effects of sample rate on signal processing. In this discussion, the Nyquist-Shannon sampling theorem establishes a minimum sampling rate of twice the signal frequency. Shannon's version of the theorem states:

"If a function x(t) contains no frequencies higher than B hertz, it is completely determined by giving its ordinates at a series of points spaced 1/(2B) seconds apart."

Note: the Sample Rate is set to 32khz.

### Frequency: 2000[edit]

With the frequency set at 2000, the time trace shows the expected sine wave, and the frequency plot shows a single signal at 2.0khz.

### Frequency: 15000[edit]

Setting the frequency to 15000, the frequency plot shows a single signal at 15.0khz, but the time trace shows significant degradation of the waveform.

### Frequency: 18000[edit]

Setting the frequency to 18000, the time trace not only shows significant degradation of the waveform, but the frequency plot shows a single signal at 14.0khz! This is called "aliasing", which is an artifact of insufficient sampling rate.

## Source hardware example[edit]

There are several factors which determine the rate at which data flows from one block to the next. However, many beginners assume that if, for example, a waveform source is set to a certain frequency, and a sample rate is set, then that output signal will be at that rate. But, as opposed to a hardware circuit, the signal is just data in a buffer. The following sections will illustrate this.

This discussion is based on the flowgraph of a RadioTeleTYpe (RTTY) receiver. It can be found at [1]

Frequency shift keying (FSK) tones are input to the microphone jack of the computer which has a sample rate of 48khz. That data is fed to a Frequency Xlating FIR Filter which shifts the tones above and below the center frequency. It also decimates (divides) the sample rate by 50, producing an output sample rate of 960.

The Quadrature Demod produces a signal which is positive or negative depending on whether the tone is above or below the center frequency.

The RTTY symbol time is, by definition, exactly 22 ms. yielding the familiar 45 baud (1/0.022 rounded). To get an integer number of samples per symbol, a sample rate of 500 was chosen, producing 11 samples per symbol time.

The output of the Quadrature Demod block has a sample rate of 960; the desired sample rate is 500. The Rational Resampler interpolates (multiplies) the sample rate by 500 and decimates (divides) it by 960 to produce an output sample rate of 500.

The 'Terminal Display Sink' is an Embedded Python Block which reads the input stream of 1's and 0's, synchronizes on the start bit, creates a Baudot character from the five data bits, converts Baudot to UTF-8, and outputs the characters to a ZMQ PUSH Message Sink.

## Sink hardware example[edit]

Whereas the example above is fairly straight forward, timing controlled by a hardware sink must be analyzed by starting at the output and working backwards through the flowgraph!

The following discussion is based on this flowgraph of a Morse Code generator:

For this example, the output Audio Sink has a sample rate of 48khz. This is fed by a Rational Resampler which interpolates (multiplies) the sample rate by 4, so the input sample rate must be 12000 (12khz).

The Multiply, IIR Filter, and Uchar to Float blocks do not change the sample rate.

The Repeat block takes each data item of input and repeats it 1200 times. (This is a form of interpolation.) This forces an input sample rate of 10, which is the desired baud rate. To provide for various code speeds, Variable blocks define the following:

The `speed`

variable in words per minute can be set by the user to any of the following: 2, 3, 4, 6, 8, 12, 16, or 24 (all are factors of 48).

The `baud`

variable = speed / 1.2

The `repeat`

variable is fixed at 1200.

The `samp_rate`

variable = baud * repeat

The 'Morse code vector source' is an Embedded Python Block which gets characters from the 'QT GUI Message Edit Box' and converts them into vectors, where each 1 is a dot bit time and each 0 is a space of one bit time. The complete description of Morse Code is given here. The Morse Code generator project, including the flowgraph and Python code, can be found in gr-morse-code-gen.

## When there is no hardware block[edit]

Some flowgraphs, such as for testing or simulation, do not involve any hardware devices to set a sample rate. In those cases a Throttle block can be used instead.

This flowgraph shows the usage of AND, OR, and XOR logic blocks. Since no hardware devices are involved, the Throttle block assures that the processor will not lock up trying to process the data at its maximum possible speed.

Note that the Throttle block doesn't even need to be in the 'main' data path to work.