Sample Rate Tutorial: Difference between revisions

From GNU Radio
Jump to navigation Jump to search
(→‎When there is no hardware block: Removed wrong information.)
Line 71: Line 71:
== When there is no hardware block ==
== When there is no hardware block ==


Some flowgraphs, such as for testing or simulation, do not involve any hardware devices to set a sample rate. In those cases a Throttle block can be used instead.
Some flowgraphs, such as for testing or simulation, do not involve any hardware devices to set a sample rate. In those cases a [[Throttle]] block can be used instead.


Note that the Throttle block only does one thing: It copies its input to its output, but waits during that operation for long enough such that the average rate of samples being copied is as specified. This means it's only effective when it's part of the sample flow that you want to reduce in rate.
'''[[Throttle]] is not adequate when the sampling rate is already defined by a sampling hardware device, like a sound card or an SDR frontend (USRP etc.)!'''
 
[[Throttle]] simply slows down the ''processing'' of samples, and does nothing to the samples themselves. Since GNU Radio blocks can only process signal as long as there is some input in their input buffer(s) and as long as there is some space for the output in their output buffer(s), Throttle can effectively limit the throughput of a flow graph by limiting how many samples it copies from its own in- to its output, or by only consuming samples at a limited rate.
 
This is very useful in situations where you want to look at a synthetic signal in a visualization:
 
[[File:demonstrate_throttle.png]]
 
This is an example from the [[Throttle]] block documentation. In the upper component, the rate at which the [[Signal Source]] can produce is limited by Throttle consuming them at the specified average rate. In the lower component, the other [[Signal Source]] is not limited by anything but how fast your CPU can produce data and shuffle it into the [[Qt GUI Time Sink]] – leading to both a fully occupied CPU core just generating the signal, and a practically useless visualization in the "Unthrottled" Qt GUI Time Sink.

Revision as of 10:14, 27 July 2023

Demonstrate the effects of Sample Rate with GRC

The following flowgraph will be used to demonstrate the effects of sample rate on signal processing. In this discussion, the Nyquist-Shannon sampling theorem establishes a minimum sampling rate of twice the signal frequency. Shannon's version of the theorem states:

If a function contains no frequencies higher than hertz, it is completely determined by giving its ordinates at a series of points spaced seconds apart.

Note: the Sample Rate is set to 32 kHz.

Samp rate demo fg.png

Frequency: 2000

With the frequency set at 2000, the time trace shows the expected sine wave, and the frequency plot shows a single signal at 2.0 kHz.

Samp rate demo out1.png

Frequency: 15000

Setting the frequency to 15000, the frequency plot shows a single signal at 15.0 kHz, but the time trace shows significant degradation of the waveform.

Samp rate demo out2.png

Frequency: 18000

Setting the frequency to 18000, the time trace not only shows significant degradation of the waveform, but the frequency plot shows a single signal at 14.0 kHz! This is called aliasing, which is an artifact of insufficient sampling rate.

Samp rate demo out3.png

Source hardware example

There are several factors which determine the rate at which data flows from one block to the next. However, many beginners assume that if, for example, a waveform source is set to a certain frequency, and a sample rate is set, then that output signal will be at that rate. But, as opposed to a hardware circuit, the signal is just data in a buffer. The following sections will illustrate this.

This discussion is based on the flowgraph of a RadioTeleTYpe (RTTY) receiver. It can be found at [1]

RTTY rcv.png

Frequency shift keying (FSK) tones are input to the microphone jack of the computer which has a sample rate of 48 kHz. That data is fed to a Frequency Xlating FIR Filter which shifts the tones above and below the center frequency. It also decimates (divides) the sample rate by 50, producing an output sample rate of 960.

The Quadrature Demod produces a signal which is positive or negative depending on whether the tone is above or below the center frequency.

The RTTY symbol time is, by definition, exactly 22 ms. yielding the familiar 45 baud (1/0.022 rounded). To get an integer number of samples per symbol, a sample rate of 500 was chosen, producing 11 samples per symbol time.

The output of the Quadrature Demod block has a sample rate of 960; the desired sample rate is 500. The Rational Resampler interpolates (multiplies) the sample rate by 500 and decimates (divides) it by 960 to produce an output sample rate of 500.

The 'Terminal Display Sink' is an Embedded Python Block which reads the input stream of 1's and 0's, synchronizes on the start bit, creates a Baudot character from the five data bits, converts Baudot to UTF-8, and outputs the characters to a ZMQ PUSH Message Sink.

Sink hardware example

Whereas the example above is fairly straight forward, timing controlled by a hardware sink must be analyzed by starting at the output and working backwards through the flowgraph!

The following discussion is based on this flowgraph of a Morse Code generator:

MorseGen fg.png

For this example, the output Audio Sink has a sample rate of 48 kHz. This is fed by a Rational Resampler which interpolates (multiplies) the sample rate by 4, so the input sample rate must be 12000 (12 kHz).

The Multiply, IIR Filter, and Uchar to Float blocks do not change the sample rate.

The Repeat block takes each data item of input and repeats it 1200 times. (This is a form of interpolation.) This forces an input sample rate of 10, which is the desired baud rate. To provide for various code speeds, Variable blocks define the following:

The speed variable in words per minute can be set by the user to any of the following: 2, 3, 4, 6, 8, 12, 16, or 24 (all are factors of 48).

The baud variable = speed / 1.2

The repeat variable is fixed at 1200.

The samp_rate variable = baud * repeat

The 'Morse code vector source' is an Embedded Python Block which gets characters from the 'QT GUI Message Edit Box' and converts them into vectors, where each 1 is a dot bit time and each 0 is a space of one bit time. The complete description of Morse Code is given here. The Morse Code generator project, including the flowgraph and Python code, can be found in gr-morse-code-gen.

When there is no hardware block

Some flowgraphs, such as for testing or simulation, do not involve any hardware devices to set a sample rate. In those cases a Throttle block can be used instead.

Throttle is not adequate when the sampling rate is already defined by a sampling hardware device, like a sound card or an SDR frontend (USRP etc.)!

Throttle simply slows down the processing of samples, and does nothing to the samples themselves. Since GNU Radio blocks can only process signal as long as there is some input in their input buffer(s) and as long as there is some space for the output in their output buffer(s), Throttle can effectively limit the throughput of a flow graph by limiting how many samples it copies from its own in- to its output, or by only consuming samples at a limited rate.

This is very useful in situations where you want to look at a synthetic signal in a visualization:

Demonstrate throttle.png

This is an example from the Throttle block documentation. In the upper component, the rate at which the Signal Source can produce is limited by Throttle consuming them at the specified average rate. In the lower component, the other Signal Source is not limited by anything but how fast your CPU can produce data and shuffle it into the Qt GUI Time Sink – leading to both a fully occupied CPU core just generating the signal, and a practically useless visualization in the "Unthrottled" Qt GUI Time Sink.