Frequency Shifting

Beginner Tutorials Introducing GNU Radio What is GNU Radio? Installing GNU Radio Your First Flowgraph Flowgraph Fundamentals Python Variables in GRC Variables in Flowgraphs Runtime Updating Variables Signal Data Types Converting Data Types Packing Bits Streams and Vectors Hier Blocks and Parameters Creating and Modifying Python Blocks Creating Your First Block Python Block With Vectors Python Block Message Passing Python Block Tags DSP Blocks Low Pass Filter Example Designing Filter Taps Sample Rate Change Frequency Shifting Reading and Writing Binary Files SDR Hardware RTL-SDR FM Receiver B200-B205mini FM Receiver

This tutorial describes how to perform frequency shifting, causing the frequency of a signal to change.

The previous tutorial, Sample Rate Change, describes how to both increase and decrease the sampling rate. The next tutorial, Reading and Writing Binary Files, describes how to read and write radio waveform captures as binary files.

Frequency Shifting

Frequency shifting is the process of changing the position of a signal within the frequency domain. Equivalently, it can be stated that frequency shifting is the process of changing the center frequency of a signal. Frequency shifted can be implemented many different ways, although this tutorial will focus on the simple method of multiplication by a complex sinusoid.

Multiplying a signal by a complex sinusoid with frequency f Hz will translate or shift the center frequency of the signal by f Hz. For example, to frequency shift a signal by 1 MHz a complex signal must be generated with frequency 1 MHz, and then multiplied against the desired signal in order to frequency shift it.

Build Example Signal

First an example signal needs to be built. A simple signal of filtered noise is created. Drag in the following blocks and connect them:

• Noise Source
• Throttle
• Low Pass Filter
• QT GUI Frequency Sink

The flowgraph is an offline simulation to the choice of sampling rate is somewhat arbitrary, but a sample rate of 10 MHz is chosen to realistic number.

The low-pass filter properties are updated to define the cutoff frequency and transition width:

• Cutoff Freq: samp_rate/8
• Transition Width: samp_rate/16

Running the flowgraph then displays a simulated signal:

The signal has not been shifted yet and therefore has a center frequency of 0 Hz.

Create Complex Sinusoid

A complex sinusoid is added to the flowgraph which will be used later to perform the frequency shifting. Add the following blocks and connect them to the flowgraph:

• Variable
• Signal Source

The flowgraph is an offline simulation to the choice of sampling rate is somewhat arbitrary, but a sample rate of 10 MHz is chosen to be a realistic number.

The variable new_center_frequency is then used for the frequency in the signal source block:

Increase the number of ports on the QT GUI Frequency Sink:

Now run the flowgraph:

You can now see the new complex sinusoid that has been created and displayed in red:

The frequency shifting process will apply the blue signal against the red complex sinusoid, centering it at 1 MHz.

Perform Frequency Shifting

Add the Multiply block into the flowgraph and connect it such that it accepts the outputs from Low Pass Filter and Signal Source:

The multiply block now performs the frequency shifting, moving the center frequency of the signal up to 1 MHz. Running the flowgraph shows the input signal centered at 0 Hz and the frequency shifted version at 1 MHz:

The frequency shifted value can be positive or negative. Update the new_center_frequency variable to be -3 MHz:

Running the flowgraph now shows the signal centered at -3 MHz:

A QT GUI Range block can be used to change the center frequency in real time. Right click on the new_center_frequency and select Disable:

The block will now be grayed out.

Add a QT GUI Range block to the flowgraph:

Open the QT GUI Range block and update the following properties:

• ID: new_center_frequency
• Default Value: 0
• Start: -samp_rate/2
• Stop: samp_rate/2

Save the properties and run the flowgraph. The QT pop up window will now display a slider bar at the top which can be clicked and slid around to change the frequency and therefore move the frequency shifted signal. The text box can also be modified to set a specific center frequency:

The next tutorial, Reading and Writing Binary Files describes how to read and write radio waveform captures as binary files.