User:Duggabe: Difference between revisions
Jump to navigation
Jump to search
(first draft of section 1) |
|||
| Line 1: | Line 1: | ||
The first section of this tutorial explains how an Amplitude Modulated (AM) signal can be created. Rather than using any real hardware for transmission, the signal is sent via a socket to the second section of the tutorial which explains how to demodulate the received signal. The only actual hardware involved is the computer's microphone input and speaker output. In the case of a Raspberry Pi computer, which has no microphone input, an alternative is presented. | |||
This tutorial can be performed with either GNU Radio (GR) version 3.7 or 3.8 (and later). The Graphical User Interface gnuradio-companion (GRC) is used to create a flowgraph for each section. | |||
== | == Prerequisites == | ||
* | * [[Guided_Tutorial_GRC|'''Intro to GR usage: GRC and flowgraphs''']] | ||
* [[Sample_Rate_Tutorial|'''Understanding sample rate''']] | |||
== | == AM transmitter == | ||
Using gnuradio-companion (GRC), build this flowgraph of the transmitter section: | |||
* | |||
* | [[File:AM_transmit_fg.png|800px]] | ||
* | |||
* | === Block descriptions === | ||
* | * The Options block identifies the filename for the flowgraph, a title, author, etc. | ||
* | * The microphone input is defined by an Audio Source block. The parameters are: | ||
* | ** Sample rate - set to 48khz | ||
* | ** Device name - for most microphone jacks built into the computer, the Device name can be left blank; for other cases, see [[Audio_Source#Device_Name]] | ||
* | * For the remainder of the flowgraph, a sample_rate of 768khz is used. This value is set in the Variable block. This value was chosen to give the 48khz carrier frequency 16 samples per cycle (48000 x 16 = 768000). | ||
* To boost the 48khz sample rate of the audio input to the 768khz sample rate, a Repeat block with a value of 16 is used. | |||
* The QT GUI Range block defines an Audio gain (volume) control with a range of 0 to 10. The default (starting) value is 1. | |||
* The value of the volume control is used as a multiplier in the Multiply Const block. | |||
* To create an AM signal, the carrier signal is multiplied by the audio signal plus one. The constant 1 creates the carrier when no audio is present. | |||
* The carrier signal (in this example is 48khz) is generated by the Signal Source block. | |||
* For a real radio transmitter, the output of the Multiply block would be fed to band-pass filters and then to Radio Frequency (RF) hardware. For this tutorial, we are sending the transmit signal to a data socket connected to the receiver section. | |||
=== Note for Raspberry Pi === | |||
Since a Raspberry Pi has no audio input jack, there are two alternatives: | |||
# use a USB audio dongle as is shown in the flowgraph. | |||
# replace the Audio Source block with a Signal Source block and a Throttle block. | |||
=== Test transmitter section === | |||
== AM receiver == | |||
=== Block descriptions === | |||
=== Testing === | |||
Revision as of 13:13, 10 April 2020
The first section of this tutorial explains how an Amplitude Modulated (AM) signal can be created. Rather than using any real hardware for transmission, the signal is sent via a socket to the second section of the tutorial which explains how to demodulate the received signal. The only actual hardware involved is the computer's microphone input and speaker output. In the case of a Raspberry Pi computer, which has no microphone input, an alternative is presented.
This tutorial can be performed with either GNU Radio (GR) version 3.7 or 3.8 (and later). The Graphical User Interface gnuradio-companion (GRC) is used to create a flowgraph for each section.
Prerequisites
AM transmitter
Using gnuradio-companion (GRC), build this flowgraph of the transmitter section:
Block descriptions
- The Options block identifies the filename for the flowgraph, a title, author, etc.
- The microphone input is defined by an Audio Source block. The parameters are:
- Sample rate - set to 48khz
- Device name - for most microphone jacks built into the computer, the Device name can be left blank; for other cases, see Audio_Source#Device_Name
- For the remainder of the flowgraph, a sample_rate of 768khz is used. This value is set in the Variable block. This value was chosen to give the 48khz carrier frequency 16 samples per cycle (48000 x 16 = 768000).
- To boost the 48khz sample rate of the audio input to the 768khz sample rate, a Repeat block with a value of 16 is used.
- The QT GUI Range block defines an Audio gain (volume) control with a range of 0 to 10. The default (starting) value is 1.
- The value of the volume control is used as a multiplier in the Multiply Const block.
- To create an AM signal, the carrier signal is multiplied by the audio signal plus one. The constant 1 creates the carrier when no audio is present.
- The carrier signal (in this example is 48khz) is generated by the Signal Source block.
- For a real radio transmitter, the output of the Multiply block would be fed to band-pass filters and then to Radio Frequency (RF) hardware. For this tutorial, we are sending the transmit signal to a data socket connected to the receiver section.
Note for Raspberry Pi
Since a Raspberry Pi has no audio input jack, there are two alternatives:
- use a USB audio dongle as is shown in the flowgraph.
- replace the Audio Source block with a Signal Source block and a Throttle block.